服务热线 18660772233
0531-55536261
联系在线客服

自动门电机厂家分享振动电机经常被忽视的小问题

来源:http://www.jnmcd.com 发布时间:2020-05-11 浏览:
  振动电机是各种振动机械设备共同的振动源,也是振动设备的核心,一旦振动电机出现故障,振动设备就不得不停止!在实际应用中,往往忽略了振动电机存在的一些致命问题。做好日常维护工作,解决这些小问题可以起到事半功倍的效果。山东自动门电机厂家现在告诉你关于振动电机在使用中经常忽略的问题!
  Vibration motor is the common vibration source of all kinds of vibration mechanical equipment, and also the core of vibration equipment. Once the vibration motor fails, the vibration equipment has to stop! In practical application, some fatal problems of vibration motor are often ignored. Do a good job in daily maintenance, solve these small problems can play a multiplier effect. Shandong automatic door motor manufacturers now tell you about the vibration motor in use often ignored!
山东自动门电机
  1.振动电机的轴承应定期加油,一般每2 - 3个月加油一次。喷嘴可以用油枪加注或停止加油。注油能力为轴承室容积的1/3 ~ 2 ~ 1。
  1. The bearing of vibration motor shall be oiled regularly, usually every 2-3 months. The nozzle can be filled or stopped with an oil gun. The oil filling capacity is 1 / 3 ~ 2 ~ 1 of the bearing chamber volume.
  2.振动电机在运行时如有较大声响,应及时停机查找故障点,故障点可在运行前排除。
  2. If there is a loud noise during the operation of the vibration motor, it shall be stopped in time to find the fault point, which can be removed before the operation.
  3.当激振力调整时,内侧面为固定极化块,应沿轴向固定。然后将中间轴上的外可调极化块调到相同方向的对角。
  3. When the exciting force is adjusted, the inner side is fixed polarization block, which should be fixed along the axial direction. Then adjust the external adjustable polarization block on the intermediate shaft to the opposite corner in the same direction.
  4.振动电机一般小修一次,大修一年,运行3~6个月。在小修期间,要清除机身积尘,检查线圈的绝缘电阻和接线是否可以加强,以便实时消除隐患。大修时,打开电机,清除机体内外积聚的灰尘,检查轴承磨损情况,检查接地和紧固螺栓是否松动,并实时紧固,清洗轴承,更换新的润滑脂。
  4. Generally, the vibration motor shall be repaired once, overhauled for one year and operated for 3-6 months. During the minor repair, it is necessary to remove the dust on the body and check whether the insulation resistance and wiring of the coil can be strengthened, so as to eliminate the hidden danger in real time. During the overhaul, open the motor, remove the dust accumulated inside and outside the machine body, check the bearing wear, check whether the grounding and fastening bolts are loose, and fasten in real time, clean the bearing, and replace with new grease.
  5.电机线圈的绑扎和螺栓的紧固必须牢固可靠,电缆、油封和防尘垫必须完好无损。
  5. The binding of motor coil and the fastening of bolt must be firm and reliable, and the cable, oil seal and dust-proof pad must be intact.
  6.振动电机轴向间隙过大,更换轴承时应选择原轴承型号。
  6. The axial clearance of the vibration motor is too large, so the original bearing model should be selected when replacing the bearing.
  以上是山东自动门电机厂家为大家介绍的相关内容,想要了解更多内容,欢迎访问网站:http://www.jnmcd.com
  The above is the relevant content introduced by Shandong automatic door motor manufacturer. To learn more, please visit the website: http://www.jnmacd.com
推荐新闻
  • 联系人:张经理
  • 手机:18660772233(微信同号)
  • 电 话:0531-55536261 / 0531-55536272
  • 邮 箱:911510021@qq.com
  • 地 址:山东济南市济南时代欧亚电子大厦一楼A111号
  • Copyright © 2018 济南美磁达电子有限公司 All Rights Reserved