服务热线 18660772233
0531-55536261
联系在线客服

微型电机润滑油该多久检查一次?

来源:http://www.jnmcd.com 发布时间:2018-12-03 浏览:
我们在使用微型减速机前,一定要特别注意润滑油的检查和替换,以保证微型减速机能取得良好的润滑。微型减速机所运用的润滑油必须为规矩品牌及规矩类型,不同的润滑油制止混合运用,且关于润滑油油位、油质的检查要守时履行。那么微型减速机润滑油应该怎样检查机替换?下面就详细的为咱大家介绍:
Before using the miniature reducer, we must pay special attention to the inspection and replacement of lubricating oil to ensure that the miniature reducer gets good lubrication. The lubricating oil used in miniature reducer must be the rule brand and rule type. Different lubricating oils should be used to prevent mixing, and the inspection of lubricating oil level and oil quality should be carried out on time. Then how should the lubricating oil of the miniature reducer be checked for replacement? Following is a detailed introduction for all of us:
1、微型减速机的油位检查,微型减速机的油位是通过油面间隔油位螺栓的间隔来断定的,油位螺栓、放油螺栓和通气器的方位是依据微型摆线减速机设备方位断定,详细在设备时的方位,能够参阅生产企业给出的微型减速机设备方位图纸。
1. Oil level inspection of miniature reducer. The oil level of miniature reducer is determined by the interval between oil level bolts. The orientation of oil level bolts, oil discharge bolts and ventilators is determined by the equipment orientation of miniature cycloid reducer. The detailed orientation of the equipment can refer to the design of miniature reducer given by the manufacturer. Bearing drawings.
微型减速机在做油位检查时,首先是先堵截微型减速机的电源,等候微型减速机冷却今后,移去油位螺栓,丈量油面与螺栓之间的方位断定润滑油剩余量,之后按照要求弥补或替换润滑油,供认油液充溢后设备油位螺栓;
In order to check the oil level of the miniature reducer, the power supply of the miniature reducer should be blocked first, and then the bolt of the oil level should be removed to measure the orientation between the oil surface and the bolt to determine the remaining amount of lubricating oil. Then, the lubricating oil should be compensated or replaced according to the requirements, and the bolt of the equipment oil level should be admitted after the oil overflowed.
2、微型减速机的油质检查,微型减速机的润滑油在运用一段时间之后可能因为各种原因此发生蜕变,因此要守时对润滑油的油质进行检查。微型减速机的油质检查首先是堵截电源并等候微型减速机冷却,之后翻开放油螺栓获取油样,假如油样出现蜕变则应马上替换润滑油;
2. Oil quality inspection of miniature reducer. The lubricating oil of miniature reducer may change after a period of time because of various reasons. Therefore, the oil quality of lubricating oil should be checked on time. The oil quality inspection of the miniature reducer is to block the power supply and wait for the cooling of the miniature reducer, then open the oil bolt to get the oil sample. If the oil sample changes, the lubricant should be replaced immediately.
山东微型电机
3、微型减速机的润滑油替换,微型减速机的润滑油替换应在机械工作温度下进行,这个时分油温较高,油的粘稠度较低,替换难度较小。微型减速机替换润滑油时,我们首先应堵截电源避免触电,等候微型减速机适当冷却至无焚烧风险后,初步替换润滑油。
3. The replacement of lubricating oil for miniature reducer should be carried out at the working temperature of the machine. At this time, the oil temperature is higher, the viscosity of the oil is lower, and the replacement difficulty is less. When replacing lubricating oil with miniature reducer, we should first stop the power supply to avoid electric shock, and wait for the miniature reducer to be properly cooled to zero burning risk, then replace the lubricating oil initially.
微型减速机的放油螺栓下放置一个接油盘,之后翻开油位螺栓、放油螺栓和通气器初步放油,等候油液全部排出后装回放油螺栓,并注入新的润滑油,润滑油的品牌类型要与原润滑油保持一起,油量与安装方位一起,通过油位螺栓调查油液到达规矩量后,拧紧油位螺栓和通气器。
The oil discharging bolt of the miniature reducer is placed under an oil disc, and then the oil level bolt, the oil discharging bolt and the ventilator are turned over to preliminary oil discharging. After waiting for the oil to be discharged, the oil bolt is loaded back and injected with new lubricating oil. The brand type of lubricating oil should be kept with the original lubricating oil, and the oil quantity and installation orientation should be kept together through the oil level. After the bolt investigates the oil reaching the required moment, tighten the oil level bolt and the ventilator.
以上的信息看完相信大家也对微型电机有一定的了解,希望我们济南美磁达电子有限公司带给你的信息能对你以后的生活有所帮助如果想要了解更多山东微型电机的信息请点击我们的网站我们的网站是:http://www.jnmcd.com谢谢你的观看!
After reading the above information, I believe you also have a certain understanding of micro-motors. I hope the information we brought to you by Jinan Meizhida Electronics Co., Ltd. will help you in your future life. If you want to know more about Shandong micro-motors, please click on our website: http://www.jnmcd.com. Thank you. Watch!
推荐新闻
  • 联系人:张经理
  • 手机:18660772233(微信同号)
  • 电 话:0531-55536261 / 0531-55536272
  • 邮 箱:911510021@qq.com
  • 地 址:山东济南市济南时代欧亚电子大厦一楼A111号
  • Copyright © 2018 济南美磁达电子有限公司 All Rights Reserved 诺商信息 网站地图 XML TXT  鲁ICP备18050301号-1

    鲁公网安备 37010502001057号